Beta75 Pro 2 is a lighter but still fast enough 2S whoop drone. With the AIO F4 2S flight controller and 0802 brushless motors, only 28g without batteries. BETAFPV always try to provide more choices for every FPV pilots. Pro series is our product line with lighter, faster and higher intergrated brushless drones.
X series, like Beta65X or Beta75X, represent the highest performance of 2S whoop drones. With long range rx, powerful ESC and motors, pilots would fly the X drone like a smaller mini drones; Pro series, like Beta65 Pro 2 and Beta75 Pro 2, have a higher integrated AIO FC and lighter weight, pilots fly it like a faster Tiny Whoop drone.This is the biggest difference of the X series and Pro series drones. You could have a noticeable different experience in control.
Here is a specification comparison of the 75mm brushless drones, Beta75X and Beta75 Pro 2.
Beta75 Pro 2 start another new era of 2S whoop drones. Compared with the Beta75X, it is 14g lighter in weight, you could fly real acro in 2S battery, like a faster Tiny Whoop drone, but is still small enough, safe enough, and quiet enough to fly anywhere.
With the high performance STM32F411 processor FC boards and tuned Betaflight Ominibus 4.0.0 firmware, everyone could fly the Beta75 Pro 2 drone like a racing pro.
Durable and light enough frame is customized for the Beta75 Pro 2. It is 2g lighter than the Beta75X frame, but have a same battery slot that compatiable with the 2S.
Whole drone no soldering or tinkering necessary. Customized lightest 0802 12000KV motors with cable connectors. Just plug and play.
2pcs 300mAh HV 1S high rate batteries are recommend by default. But pilot could also use their 2S battery with a replaced power cable. Optional and affordable.
Wash-out issue totally not exists in Beta75 Pro 2 drones.
Weight: 28g (without battery)
Motors: 0802 12000KV with connector
Frame: Beta75 Pro 2 Frame
Props: 40mm 4-blades props, 1.0mm shaft hole
Camera: AIO Camera 35 degree (by default)
Receiver Option: SPI Frsky
Battery: 300mah 1S HV Batteries 2pcs
2S AIO F4 FC Board.
Size: 26mm x 26mm, whoop mounting pattern
Firmware version: Betaflight OMNIBUSF4SD (OBSD) 4.0
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Smart Audio port is available for radio control VTX
Built-in 1-2S ESC with 5A continuous and peak 6A current
Support BLHeliSuite programmable
Factory firmware: S_H_50_REV16_7.HEX
0802 brushless motors only weighs 1.9g with connector. This motor is customed for 2S brushless build (Beta65X / Beta75 Pro 2). A 1.0mm header pins connector is include. So no soldering needed, just plug and play.
AIO Camera VTX
On the Beta75 Pro 2, it is the customized version lighter AIO VTX camera, only 2.9g.
Output power: 25mW
Smart Audio function is included for radio control
Antenna: Dipole ANT
Frequency: 5.8GHz 6 bands 48 channels, with Raceband: 5362~5945MHz
TV System: PAL
Field of view: 100-120 degrees with 1/4 lens
The Beta75 Pro 2 drone comes with "props out" in default. Why we need "props out" direction?
Default Betaflight props direction, quadcopter dips and "washes out" in hard corners. With reversed props or "props out", no more dipping even in hardest cornering.
CUSTOMIZED AIO CAM & VTX
The AIO camera VTX on the Beta75 Pro 2 is a customed version of Z02. The VTX board and camera board are split and 35 degree camera mount for more fast flying. Only 25mW power output is provided in stock. Besides, it have almost all the other function of the Z02 camera, like smart audio etc.
1 x Beta75 Pro 2 BNF 2S Whoop Quadcopter
2 x 300mAh 1S HV battery (Not for PNP version)
1 x Spare camera mount with 25 degree tilt
Note: Due to the battery in it, we could not send it by DHL or EMS. If you need it arrive fast, please write "Remove battery" in the comment.