ARRIS X-Speed 250B V3.0 with Fatshark Dominator V3 goggle is the latest FPV250 version of ARRIS X-Speed. It is fully assemble, tuned and tested by the technician before leaving the factory. The drone comes with Raptor 390 Tower w/ 30A 4in1 ESC + F3 + OSD + PDB, ARRIS S2205 2300KV brushless motor,5042 high efficiency 3 blade propeller, 700TVL HD camera,5.8g 200mw FPV TX and antenna, Radiolink AT9 with R9DS receiver and 4S 1500mah lipo battery and charger. What you need to do is preparing the battery for the goggle, then you can start your FPV journey.
1. Simple structure frame installed with tower structure ESC/PDB, easy to assemble and easy to repair.
2. Big inner space, 268mm wheeabase, 6inches propeller and other equipements is compatible
3. The tower comes with integrated OSD, no need to install it separately
4. The angle of the FPV camera is adjustable from 0 to 45 degree
5. 4mm thick arms, super strong and durable
6. Newly released high efficiency S2205 2300KV motor provides you better performance and longer working life
7. High safety 4S 1500mah 50C lipo battery
Dimension: 7.88 x 9.35 x 2.63 (inches)
Diagonal Wheelbase: 268mm (10.55inches)
Flight Controller: F3 flight controller
Frame Material: Carbon/glass fiber composited sheet
BNF weight: 400g
Radio System: RadioLink AT9 9-CH radio with Receiver
Camera: 700TVL HD video camera
FPV TX: 5.8G 200mw 32CH
Antenna: 5.8G Antenna
Flying Time: 10min hovering
Battery: ARRIS 4S 1500mah lipo battery
Charger: Imax B6 mini charger with adaptor
Goggle: Fatshark Dominator V3 FPV Goggle
Receiver: FatShark NexWave RF 5G8 32CH Race Band Receiver FSV2442
One of the main change on the ARRIS X-Speed 250B V3.0 is the Raptor 390 tower we use. Why we choose it?
1. The two layers tower structure ESC is highly integrated design products,decreasing the interference caused by signal transmission. The factory optimized the PCB layout and the pins, connecting all the electronic components on the board,avoid soldering and wiring.On this tower,the pins connect the flight controller board and the ESC board,maximally decrease the interference caused by signal transmission,
2. The Tower structure design could protect the ESC well during the flight.ESC is one of the most easily broken parts on the drones except the propellers. According to our experience,some of the ESC were damaged by the propeller rotation or tree brunch cut after the damage when it installed on top of the motor arm.Some of the ESC were damaged due to the broken of the motor arm during the crash.For this tower, the esc integrated in the tower which installed in the middle of the quad frame, the ESC's can be protected quite well.
3. Raptor 390 tower makes the assembling of the fpv racing drones more and more convenient,the wires tidy and concise.Using this tower, you just need to solder the 4 motor wires to the holes, so easy. The lower board integrated the 4in1 ESC,the power port is in the center,bulge a bit over. This could not only make the connecting wires more convenient, but also avoid to interrupt the esc output port on the two sides. The upper board F3 flight controller board integrated with the OSD. There is also 5V,12V and BATV for powering the camera,video tx,LED and other equipments.
4. Small size and light weight tower fit for all sizes of the quad,and make the center of gravity of the drone lower. The weight of the raptor 390 tower is only 22g, with two layers tower structure, the height is only 15.1mm.
And there are two plates on the tower,one is 4in1 ESC, and the other is the FC flight controller. If some of the components on the tower damaged, you just need to change one plate of the tower. Also it integrated with the OSD on it, you do not need to install extra OSD on the F3 separately.
ARRIS X-Speed 250B comes with the latest version motor--ARRIS S2205 2300KV brushless Motor.
1. Knul Design: This design ensure the stability of prop installation.
2. High quality magnets: ARRIS S2205 2300KV brushless motor adopts N52SH curved magnets to ensure the motor have more power and efficiency
3. NSK bearing: ARRIS S2205 2300KV adopts 0.2mm Japan imported stators, ultra hardness aerospace aluminum and precision cnd, which make the motor more efficiency and prolong the working life.
4. Low center design: The height of the ARRIS S2205 allows a lower center of gravity closer to the mounting point, with this, the drone can fly smoothly.
5. Cooling system: The cooling system make the motor more air flow.
6. Hollowed steel prop shaft: with this, you do not need to worry of damaging threads during crashes.
The propeller we adapts on the X-Speed 250B V3.0 version is theARRIS 5042 high efficiency 3 blade propellers. It is very powerful and well balanced. It has 10% higher efficiency than normal propellers. Perfectly suitable for FPV racing.
Thediagonal wheelbaseof the ARRIS X250B frame is about268mm, and the inner space between upper plate and lower plate is quite big. Customer can upgrade or do some modifications as you like. For example, you can install 6 inches propellers on it.
As all we know, the arm is easily broken part during the crash. ARRIS X-Speed 150B adopts4mm thickness arms, the arm is made of carbon and glass fiber composited plate,and there is almost no hollow design cut on the motor arm, so the weight is a little heavier than the 3mm one, but it improves the strength of the drone.
Many people like to is install one sport camera on top of the frame to record the videos like us. Considering this, we added a damper plate there, it can decrease much vibration from the frame, provide you better quality videos of the flight.In the mean time,the fpv camera angle i adjustable,the angle adjustable range is 0 to 45 degree. (pitch up)This could meet the requirements in different situation.
On the ARRIS X-Speed 250B V3.0, we abandoned the PCB board. Many customer reflects the captivator is easily took off, the PCB is easily damaged during the crash or caused the short out on the wire. The Raptor 390 Tower w/ 30A 4in1 ESC + F3 + OSD + PDB solved this problem perfectly.
High Brightness LED. ARRIS X-Speed 250B comes with a high brightness LED .And you can change the color of the LED light through the DIP switches. 7 color for you to choose.
ARRIS 5.8g 200mW 40-CH video TX pre-assembled.The ARRIS TS5823S transmitter packs 200mW of ultra clean 5.8GHz power in a micro sized video/audio transmitter! A must for those looking save size and weight while still getting good performance. The ARRIS TS5823S is transmitting a full range of 40 channels and only weighs 10g. It's perfect for a wide range of aircraft!With a goggle or monitor in hand, you can begin your FPV journey.
ARRIS X-Speed 250B has integrated with a remote controller battery warning buzzer, pilot can set the threshold (adjustable) according to CF parameter-adjustment software. In addition, you can also locate your racing drone through triggering the buzzer with the switch D on the transmitter.
Self-level modeis the easiest to fly, because when you leave the stick at the center and not controlling it, your drone just level itself and stays there. But Most advanced pilots would tell you they fly in Acro mode ALL THE TIME. Here are some of the advantages of Acro mode.
Manual modeis useful for acrobatics such as flips or rolls, or FPV when smooth and fast control is desired. The picture below is what we set on our own Radiolink AT9 Radio.
RadioLink AT9 9-Channel 9CH 2.4GHz Transmitter + R9D Receiver.The AT9 radio is with high performance-price ratio. And it can support strength, receiver voltage monitored, extending battery voltage, temperature, motor RPM, GPS etc.
High safety ARRIS 4S 1500mah Lipo Battery
ARRIS 4S 1500mAh 50C lipo battery is specially designed for FPV racer. The price of this battery is much higher than the similar batteries in the market, because we only sell top-quality batteries. As we all know, the low quality battery might have potential safety hazard, we will never tolerate such products.For ARRIS 4S 1500mah lipo battery, we have done UN38.3 test,1.2M Drop test,MDS report for it, for the test report, you can checkhere.
IMAX B6mini Professional Balance Charger/Discharger
SKYRC B6 mini is a high-performance, micro processor control charge/discharge station with battery management suitable for use with all current battery types, with integral equalizer for six-cell Lithium- Polymer (LiPo), Lithium-Ferrum (LiFe) and Lithium-Ion (LiIon) batteries; maximum 6A charge current and maximum 60W charge power.
Input voltage: DC11-18V
Circuit power: Max Charge (60W)
Discharge power: 5W
Charge current range: 0.1-6.0A
Discharge current range: 0.1-2.0A
LiPo/LiFe/Lilon Cells: 1-6S
NiMH/NiCd Cells: 1-15S
Pb battery voltage: 1-10P (2-20V)
Net weight: 237g
Dimensions: 107 x 85 x 34mm
Farshark Dominator V3 FPV Goggle
FOV (field of view): 30 degree diagonal (the same plastic optics as DOMV2)
Interpupillary Distance (IPD): 59 to 69 mm (adjustable)
Optional Diopter Lens Inserts: -2, -4, -6 dpt
Mode Selection (Wired/Wireless)
||Power Supply: 7 - 13 V (2S/3S supply)
Power Consumption: 390mA wireless/ 230mA direct mode (no RX)
Driver Board: Using the same as HD's, support Side/Side 3D
RF Modules: Infinite channel support on multiple bands
Head Tracker: Modular(sold separately)
Analog DVR: MicroSD support to 32Gb
Record Rate: 6Mbps (MJPG compression, 30 fps, AVI)
File playback (native recording, no codec support)
Upgradeable via SD card
PAL/NTSC continuous scan auto detect/mode change
Auto save if power removed
DVR stay off when not switched on
||800 x 480 WVGA LCD
Polarized LED backlight
NTCS/PAL auto selecting
Input HDMI 16:9
Video 4:3 horizontally stretched
(Current A/C chip only supports to 720p 50/60 Hz, could be upgraded to 1080p in the future)
||Ergonomic molded headset w/ adjustable headband
Dimensions: 169.2 x 80 x 45.5 mm
Weight: 152 g
||7.4V, 1.8A (13.32Wh)
||3.5mm AV in/out port
Power in port
3.5mm 3p earphone port
MiniDIN4 data port (head tracking)
MicroSD insert slot
RF module port
||Compatibility is only guaranteed with Fat Shark and ImmersionRC transmitters.
1 xARRIS X-Speed 250B V3 Racing Quad Frame
2 xARRIS S2205 2300KV Brushless Motors CW
2 xARRIS S2205 2300KV Brushless Motors CCW
4 xARRIS 5042 3-blade Propeller (2CW + 2CCW)
1 xRaptor 390 Tower with 30A 4in1 ESC/FC/PDB/OSD
1 x700TVL 2.8mm camera
1 x5.8G 200mw 32CH FPV TX
1 xFPV Transmitter Antenna
1 xRadiolink AT9 Transmitter + RD9 Receiver
1 xARRIS 4S 1500mah Lipo Battery
1 xIMAX B6mini Professional Balance Charger/Discharger
1 xIMAX B6 mini charger adaptor
1 xFatshark Dominator V3 FPV Goggle
Note: For this FPV Boundle, you may receive more than one parcels. One with the goggle, and the other with the rest of the items.
The goggle did not come with battery, please prepare the battery for it.