Note: ESC is upgrade to 2-4S BLS 30A.
Camera upgrade to Foxeer Arrow mini pro fpv camera.
ARRIS X-Speed 250B V3.0 is the latest version of ARRIS X-Speed. It is fully assemble, tuned and tested by the technician before leaving the factory. It comes with Raptor 390 Tower w/ 30A 4in1 ESC + F3 + OSD + PDB, ARRIS S2205 2300KV brushless motor,5042 high efficiency 3 blade propeller, 1000 TVL HD camera,5.8g 200mw FPV TX and antenna, Flysky FSI6 Radio with receiver and 4S 1500mah lipo battery. Plug the battery, turn on the goggle, you can begin your FPV journey.
1. Simple structure frame installed with tower structure ESC/PDB, easy to assemble and easy to repair.
2. Big inner space, 268mm wheeabase, 6inches propeller and other equipements is compatible
3. The tower comes with integrated OSD, no need to install it separately
4. The angle of the FPV camera is adjustable from 0 to 45 degree
5. 4mm thick arms, super strong and durable
6. Newly released high efficiency S2205 2300KV motor provides you better performance and longer working life
7. High safety 4S 1500mah 50C lipo battery
Dimension: 7.88 x 9.35 x 2.63 (inches)
Diagonal Wheelbase: 268mm (10.55inches)
Flight Controller: F3 flight controller
Frame Material: Carbon/glass fiber composited sheet
BNF weight: 400g
Radio System: Flysky FSI6 Radio with receiver
Camera: 1000TVL HD video camer
FPV TX: 5.8G 200mw 32CH
Antenna: 5.8G Antenna
Flying Time: 10min hovering
Battery: ARRIS 4S 1500mah lipo battery
Goggle:Eachine EV008 FPV goggle
One of the main change on the ARRIS X-Speed 250B V3.0 is the Raptor 390 tower we use. Why we choose it?
1. The two layers tower structure ESC is highly integrated design products,decreasing the interference caused by signal transmission. The factory optimized the PCB layout and the pins, connecting all the electronic components on the board,avoid soldering and wiring.On this tower,the pins connect the flight controller board and the ESC board,maximally decrease the interference caused by signal transmission,
2. The Tower structure design could protect the ESC well during the flight.ESC is one of the most easily broken parts on the drones except the propellers.According to our experience,some of the ESC were damged by the propeller rotation or tree brunch cut after the damage when it installed on top of the motor arm.Some of the ESC were damaged due to the broken of the motor arm during the crash.For this tower, the esc integrated in the tower which installed in the middle of the quad frame, the ESCs can be protected quite well.
3. Raptor 390 tower makes the assembling of the fpv racing drones more and more convenient,the wires tidy and concise.Using this tower, you just need to solder the 4 motor wries to the holes, so easy. The lower board integrated the 4in1 ESC,the power port is in the center,bulge a bit over. This could not only make the connecting wires more convenient, but also avoid to interrupt the esc output port on the two sides. The upper board F3 flight controller board integrated with the OSD. There is also 5V,12V and BATV for powering the camera,video tx,LED and other euipements.
4. Small size and light weight tower fit for all sizs of the quad,and make the center of gravity of the drone lower. The weight of the raptor 390 tower is only 22g, with two layers tower structure, the height is only 15.1mm.
And there are two plates on the tower,one is 4in1 ESC, and the other is the FC flight controller. If some of the components on the tower damaged, you just need to change one plate of the tower. Also it integrated with the OSD on it, you do not need to install extra OSD on the F3 seperately.
ARRIS X-Speed 250B comes with the latest version motor--ARRIS S2205 2300KV brushless Motor.
1. Knul Design: This design ensure the stability of prop installation.
2. High quality magnets: ARRIS S2205 2300KV brushless motor adopts N52SH curved magnets to ensure the motor have more power and effiency.
3. NSK bearing: ARRIS S2205 2300KV adopts 0.2mm Japan inported stators, ultra hardness aerospace aluminum and precision cnd, which make the motor more effiency and prolong the working life.
4. Low center design: The height of the ARRIS S2205 allows a lower center of gravity closer to the mounting point, with this, the drone can fly smoothly.
5. Cooling system: The cooling system make the motor more air flow.
6. Hollowed steel prop shaft: with this, you do not need to worry of damaging threads during crashes.
The propeller we adapts on the X-Speed 250B V3.0 version is the ARRIS 5042 high efficiency 3 blade propellers. It is very powerful and well ballanced. It has 10% higher effeciency than normal propellers. Pefectly suitable for FPV racing.
The digonal wheelbase of the ARRIS X250B frame is about 268mm, and the inner space between upper plate and lower plate is quite big. Customer can upgrade or do some modifications as you like. For example, you can install 6 inches propellers on it.
As all we know, the arm is easily broken part during the crash. ARRIS X-Speed 150B adopts 4mm thickness arms, the arm is made of carbon and glass fiber composited plate,and there is almost no hollow design cut on the motor arm, so the weight is a little heavier than the 3mm one, but it improves the strength of the drone.
Many people like to is install one sport camera on top of the frame to record the videos like us. Considering this, we added a damper plate there, it can decrease much vibration from the frame, provide you better quality videos of the flight.In the mean time,the fpv camera angle i adjustable,the angle adjustable range is 0 to 45 degree. (pitch up)This could meet the requirements in different situation.
On the ARRIS X-Speed 250B V3.0, we abadoned the PCB board. Many customer reflects the capicator is easily took off, the PCB is easily damaged during the crash or caused the short out on the wire. The Raptor 390 Tower w/ 30A 4in1 ESC + F3 + OSD + PDB solved this problem perfectly.
High Brightness LED.ARRIS X-Speed 250B comes with a high brightness LED . And you can change the color of the LED light through the DIP switches. 7 color for you to choose.
ARRIS 5.8g 200mW 40-CH video TX pre-assembled. The ARRIS TS5823S transmitter packs 200mW of ultra clean 5.8GHz power in a micro sized video/audio transmitter! A must for those looking save size and weight while still getting good performance. The ARRIS TS5823S is transmitting a full range of 40 channels and only weighs 10g. It's perfect for a wide range of aircraft!With a goggle or monitor in hand, you can begin your FPV journey.
FlySky FS-i6-M2 2.4GHz 6-Channel Transmitter with FS-iA6B receiver.
Channels: 6 Channels
Model Type: fixed-wing/glider/helicopter
RF range: 2.405-2.475Ghz
RF Power: Less than 20 dBm
2.4G System: AFHDS 2A and AFHDS
Code type: GFSK
Low voltage warning: Less than 4.2V
DSC port: PS2; output: PPM
Charger port: No
ANT length: 26mm*2 (dual antenna)
Power: 6V 1.5AA*4
Display mode: Transflective STN positive type,128*64 dot matric VA73*39mm, white backlight
Online update: yes
ARRIS X-Speed 250B V3.0 has integrated with a remote controller battery warning buzzer, pilot can set the threshold (adjustable) according to CF parameter-adjustment software. When you turn on the SWD switch to 2 position, the buzzer will ¡กใ beep beep¡กใ, it is easy for you to find the quad.
Self-level mode is the easiest to fly, because when you leave the stick at the centre and not controlling it, your drone just level itself and stays there. This is good for beginners.
Manual mode is useful for acrobatics such as flips or rolls, or FPV when smooth and fast control is desired. The picture below is what we set on the Flysky radio.
High safety ARRIS 4S 1500mah Lipo Battery
ARRIS 4S 1500mAh 50C lipo battery is specially designed for FPV racer. The price of this battery is much higher than the similar batteries in the market, because we only sell top-quality batteries. As we all know, the low quality battery might have potential safety hazard, we will never tolerate such products.For ARRIS 4S 1500mah lipo battery, we have done UN38.3 test,1.2M Drop test,MDS report for it, for the test report, you can check here.
- Separable design, 5 inch screen can be used as small monitor on radio controller or with tripod;
- HD high brightness 5inch LCD specially tuned for FPV racing;
- Built-in super sensitiveness 5.8GHz 40ch receiver, especially with RaceBand;
- Come with advanced auto-searching function ad show you the working frequency on screen;
- Built-in 3.7V/2000mAh battery, each full charge revive around 3.5hours working time;
- Wide range re-charge voltage 5-12V, power banks or 2S/3S batteries can be used as back-up power source, to prolong the working time;
- Ergonomic design fit your faces;
- Super-wide visible angle up to 82 degree;
- 92% transparent lens adopted, no distort, no blur on the adage of screen;
- Light weight 375g with 3.5hr 2000mAh battery, RTF for any scale racing game.
- 5 inch 800*480px HD high brightness LCD
||Screen size: 5.0 inch
Screen resolution: 800*480 (No blur after enlarge by the lens)
Screen brightness: 600cd/m2 with special high brightness backlight LED for outdoor FPV
View Angle: 140/120 degree(Horizontal/Vertical)
||3x boost of the video to acquire intense feel-in-there video;
92% transparent rate no distort of light;
|Battery and recharge
||Built-in 3.7V/2000mAh battery;
Each battery circle offer around 3.5hr working time;
5-12V wide recharging voltage range, typical recharging voltage is 5V
Accepts 5V power banks or 2S(7.4V)/3S(11.1V) battery as back-up power to have long working time
Build in 5.8G 40CH Raceband receive
|Frequency Band A
|Frequency Band B
|Frequency Band E
|Frequency Band F
|Frequency Band R
Weight: 375g with 3.5hr 2000mAh battery
Belt: three-ways adjustable belt
1 x ARRIS X-Speed 250B V3 Racing Quad Frame
2 x ARRIS S2205 2300KV Brushless Motors CW
2 x ARRIS S2205 2300KV Brushless Motors CCW
4 x ARRIS 5042 3-blade Propeller (2CW + 2CCW)
1 x Raptor 390 Tower with 30A 4in1 ESC/FC/PDB/OSD
1 x 1000 TVL 2.8mm camera
1 x 5.8G 200mw 32CH FPV TX
1 x FPV Transmitter Antenna
1 x Flysky FSI6 6-CH Radio with Receiver
1 x LED
1 x ARRIS 4S 1500mah Lipo Battery
1 x EV800 FPV Goggle
Battery Charger is sold separately.